Nixon-Egli Equipment Co.
Sales
Service
Locations
Employment
Contact Us
 
 
 
 

Call us at
Ontario:
(909)930-1822
Tracy:
(209)830-8600

New Equipment
  American Road
  Aquatech
  Arrow
  CEC
  East
  Ferguson
  Gradall
  Hamm
  Hi-Way
  HTC
  Johnston
  LeeBoy
  Lincoln
  Link-Belt
  Midland
  Miller
  PB Loader
  Petersen
  Rosco
  Trinity
  Vogele
  Wirtgen
  Zieman

Used Equipment
  CEC
  Hamm
  LeeBoy
  Link-Belt
  Misc
  Rosco
  Vogele

Manufacturers
         
   
PB Loader L-250C

Truck Mounted Loader with Clam Shovel

  • Price: Call for price
  • 'Load Over Cab' hydraulically operated loader
  • Suitable for mounting on a dump truck of adequate G.V.W.R. and equipped with a dump body that has 78 inch minimum inside body width, overall width of the truck axle over the studs not above 91 inches and the width of the truck cab and renders not above 90 inches.
  • Shovel:
    • Blade is a replacable 1/2 inch x 6 inch plow steel.
    • Sides are a 1/2 inch x 6 inch plow steel cutting edge, designed to allow the operator to load directly against the curb.
    • The back of the shovel is designed to allow the operator to have down pressure on the shovel and also back drag material for grading.
    • The operator will have positive control of shovel at all times.
    • Shovel capacity is 1 1/2 cubic yards and the width is not less than 92 inches.
    • Shovel shall be clam shell type. The rear half of the shovel rigidly mounted on the two side arms. The clam or front half of the shovel is hinged to the rear half in such a manner that it opens or closes by hydraulic means. Shovel is controlled from the cab of the truck.
    • Clam will open a minimum of 170 degrees.
    • Shovel will be able to pick up solid material without using the clam.
  • Arms:
    • Straight type with box girder type construction.
    • Minimum inside clearance of 92 inches.
    • The arms and shovel are removable from loader without having to remove the entire loader mechanism from the truck.
    • The arms are bolted to a solid cross shaft so as to equal the load pressure throughout the loader system.
    • The arms will not interfere with the opening of the truck doors in either the loading or traveling position.
    • Side arms supporting the shovel shall pivot on a point immediately behind the truck cab and below the truck frame.
    • Loader is supported on a separate frame or directly to the truck frame.
  • Loader:
    • The loader mechnism will not be mounted LOWER than any point of the truck chassis.
    • The mechanism is mounted in such a manner that the weight of the unit is distributed between the front and rear axle of the truck chassis.
    • The loader is powered hydraulically through a compound linkage system by means of a hydraulic pump that is driven from the truck transmission power take-off.
    • Weight of the unit will not exceed 3,200 lbs.
    • Component parts of the loader are of proper design and size to safely lift a maximum load of 5,000 lbs.
    • Loader is able to load dump body uniformly without having to shift material to the rear by raising the body.
  • Safety Switches:
    • The switches are installed so that when the power take-off is engaged, the opening of the truck doors will stall the hydraulic power and the loader can not be operated.
    • Safety switches shall also be installed on the dump body so that if there is an attempt to raise the dump body when the loader is in traveling position this will disengage the power-take off.
  • Operating:
    • The operating cycle is 15 seconds.
    • The hydraulic tank capacity is a minimum of 15 gallons with a return line filter and an inline suction strainer.
    • The controls are cab mounted and readily accessible to the operator from the driving position.
    • The hydraulic cylinders must have chrome finish shaft and adequate dirt wiper seals.
    • The unit is furnished completely and ready for mounting with pump and roller bearing power take-off that is suitable for continuous duty and all other items necessary to make a complete working unit.
    • Only two (1) - 8 inch double acting hydraulic cylinders to operate the loader.
    • Only two (2) - 2 1/2 inch double acting hydraulic cylinders to operate the clam.
   
         
 
   
 
 
Shipping Information | Return Policy | Privacy Policy | Terms of Use | Copyright © 2000-2009 Nixon-Egli Equipment Co. 2044 S. Vineyard Ave., Ontario, CA 91761 (909) 930-1822 and 800 E. Grant Line Rd., Tracy, CA 95304