Unitized Patcher

• Price: Call for price

• Container:
  • The unit shall be 4-cubic yards.
  • Double wall constructed.
  • 2 inches- 6 lb. density insulation throughout.
  • 3/16 GA HR interior sides, 12 GA HR exterior.
  • Interior walls of loading lids have expansion corrugations.
  • Flame cut upper pivot arms for opening top lids.
  • Top loading doors are 2 inches double wall constructed.
  • Doors hydraulically operate 2 inch x 11 inch stroke cylinders.
  • Material funneled to center of container.
  • Hydraulic controls located at right rear corner.
  • Material discharged by auger conveyor system.
  • Auger shall be 10 feet in length.
  • Auger to be supported at each end with sealed bearings.
  • Single speed hydraulic motor.
  • Forward and reverse controls.
  • Unit shall have an asphalt agitator.
  • Shaft designed to break asphalt, bridging due to vibratory compaction.
  • Flanged bearings each end of shaft, driven by a hydraulic motor.
• Radiant Heater:
  • Heat tubes located under container.
  • Interior heat chamber has passage ways to direct heat.
  • Passage ways separate from heat chamber.
  • Chamber totally enclosed inside container.
  • 2 burners propane fueled.
  • Rating of 67,000 BTU each @ pressure of 10 PSI.
  • Controlled by thermostat range of 100° to 300°F.
  • 12 volt ignitors electronic.
  • 100% fuel shut off if flame is extinguished.
  • Burner area fully enclosed.
• Hand Torch:
  • Pilot with valve control.
  • Capacity of 200,000 BTU.
  • 25 foot hose supplied.
• Shoveling April - Model 5:
  • Constructed of 10 GA HR steel.
  • Folding bottom for material to bypass freely.
  • Mounted on rear of container.
• Emulsion Spray Unit: Emulsified asphalt spray storage system mounted on truck chassis for applying tack coat.
• Tank:
  • Two compartment tank.
  • Storage capacity 130 gallon emulsion and 20 gallon solvent.
  • 10 gauge steel with the bottom reinforced.
  • 6 inches curbside filler cap.
  • Tank dimension 72 inchesW x 16 inchesL x 30 inchesH.
  • 4 inches clean out on curb side near tank bottom.
  • Tank shall be vented.
  • Removable fill basket strainer.
  • Y strainer at the discharge of tank before material enters the pump.
  • Capable of switching from emulsion to solvent with one valve lever.
• Heater:
  • Internal serpentine of 1 inch steel tubing to circulate water from truck engine.
  • Truck engine cooling system as a heat source.
  • Two 5/8 inch coolant hoses.
  • System will have a temperature control valve at the tank.
• Auxiliary Electric Heat:
  • Equipped with 110 VAC heat system.
  • Over night heating, controlled by temperature sensor.
  • Heating elements shall be low density stainless steel.
• Mounting:
  • Space required for mounting of tank is 22 inch.
  • Spraying system shall be mounted in front of dump body.
  • Mounting shall be accomplished with 2 full length mounts.
  • Spring bolsters on one side of tank.
  • Bolting to frame shall consist of 3 each side, 1/2 inch. There will be no welding on the truck frame.
• Pump:
  • Rotary gear pump.
  • Output of 10 gallons per minute at 600 R.P.M.
  • Pumps shall be hydraulic driven.
  • All valves shall be high pressure.
  • Pumps shall have a built in relief.
  • It shall be remote mounted for ease of maintenance.
  • Mechanically actuated from the right rear of the body.
  • Pump shall be reversible to draw material back to tank.
  • Pump shall be driven by a torque motor which has 5.9 CID.
• Spray Wand And Hose:
  • System should be plumped to curbside rear of truck.
  • 3/8 inch diameter 5 feet long steel application wand shall be supplied.
  • 25 feet of 1/2 inch diameter oil resistant hose.
  • A brass changeable nozzle at spray tip.
  • Wand storage brackets.
• Drip Pan:
  • 10 gallon drip pan/waste oil combination.
  • Mounted under patcher body.
  • Necessary valves for draining and cleaning.
• Optional equipment:
  • Auxiliary electric heat patcher:
    • low density electric heat.
    • Minimum 6kw, 240 vac thermostatically controlled.
    • 100°F to 300°F.
    • Weatherproof panel.
    • Overnight heating of asphalt.
  • Compactor lift platform:
    • hydraulic platform located at rear unit.
    • Constructed of 3/16 hr angle frame.
    • Cylinder 1 1/2 inches x 18 inches stroke.
  • Hydraulic tools:
    • Stanley BR67 breaker.
    • Asphalt cutter.
    • Detachable shank with pad.
    • (35 lb., 45 lb., 72 lb., 87 lb.) breaker sizes available.
  • Hydraulic tool circuit:
    • 25 foot dual hose.
    • Quick couplers.
    • Flow meter.
    • Engine throttle control to be provided by chassis manufacturer.
    • Relief valve.
    • Pressure gauge.
  • Tool box:
    • Lockable, 19 inches wide x 36 inches long x 19 inches high.
    • Additional sizes and configuration available.
  • Tool basket:
    • angle iron framed mounted on left side of unit.
    • 15 inchesw x 96 inches long x 8 inches high.
  • Spoils bin:
    • 2 cubic yard, cross frame spoils bin.
    • Constructed of 10 ga hr steel doors on each side to discharge material.
  • Solvent pump:
    • 12 VDC pump.
    • Connected to solvent side of tank.
    • 25 ft. hose with wand.
    • Used for cleaning tools.
  • Cab controls:
    • Inside cab controls.
    • Operates top lids.
  • Air blow gun: 25 feet, 3/8 inch hose. (Subject to air availability on chassis)
  • Arrow board:
    • (10) light board.
    • Arrow - left, right, or both.
    • Mounted at rear of unit.
  • Thermometer: 0 - 300°f.
  • Fire extinguisher: 5 lbs., 10 lbs.
  • Air compressor:
    • 24 cfm - 125 cfm.
    • Hydraulic, pto underdeck or under hood.
  • Hose reels:
    • Emulsion spray hose reel.
    • Hand torch hose reel.
    • Solvent hose reel.
    • Air blow gun hose reel.
    • Dual hose reel for jackhammer.
    • All reels are designed to accommodate 25 foot hoses.
  • LPG tank: 25 gallon upright (portable) tank or 25, 35, and 50 gallon horizontal frame mounted tank.
  • Sanding attachment:
    • equipped with broadcasting spinner.
    • (6) formed polyurethane vanes.
    • Spread width (4) feet to (40) feet.
  • Pivotal asphalt chute:
    • chute to be mounted at rear.
    • 110° pivot.
  • Side discharge conveyor:
    • 6 inches auger.
    • Hydraulic driven.
    • 5 foot in length.
    • Forward and reverse controls.
    • Pivotal at rear.
  • Compactor plate:
    • walk-behind roller with transport device
    • triangle kit
    • strobe light & beacons
    • re-emulsifying system
    • fan oil cooler
    • air type emulsion spray system
  • Double auger conveyor:
    • eliminates need for anti-bridging drive.
    • Model designation da-4.
  • General truck specifications - AC-4 unitized patcher
  • Chassis:
    • conventional or tilt cab.
    • GVW - 30,000 lbs.
    • Wheel base conventional - 175 inches minimum, tilt, - 135 inches minimum.
    • Cab to axle - 108 inches minimum - 120 inches minimum with spoils bin.
    • Reinforced frame
  • Electrical:
    • Alternator - 55 amp minimum.
    • Battery - 12 volt, 77 amp minimum.
  • Axle:
    • Front - i beam, 9,000 lbs.
    • Springs - heavy duty, 5,000 lbs. Minimum each side.
    • Rear - single speed.
    • Capacity - 21,000 lbs.
    • Springs - 10,000 lbs. With 2,600 lbs. Auxiliary.
  • Transmission: automatic 5 speed or standard 5 speed.